Zero is the longest digit in Morse code — and one of the easiest to remember. 0 in Morse code is five dashes: —–, spoken as “dah-dah-dah-dah-dah.” Once you understand why every digit has exactly five signals, zero stops being a string of dashes to memorise and becomes the logical end of a pattern you already know.
In this guide you will learn how to send, hear and practise 0, how it fits into the full 0–9 digit pattern, where it shows up in real radio and everyday use, and how to avoid the classic beginner mistake of confusing zero with the letter O. Try each example as you read — Morse code is learned by ear and by hand, not just by eye. You can check any combination instantly with a Morse Code Translator.
What Is 0 in Morse Code?
In International Morse Code, the standard system maintained under the ITU, the digit 0 is represented by five dashes with no dots: —–. A dash, or “dah,” lasts about three times as long as a dot, or “dit,” so zero is a long, steady signal: five equal long tones, each separated by a short gap.
Spoken rhythm is the fastest way to lock it in. Say it slowly out loud: dah — dah — dah — dah — dah. Keep the five dahs even and unhurried. Rushing the last two is the most common reason a listener hears something else entirely, so practise at a comfortable speed before you try to go fast.
The Digit Pattern: Why Zero Is Five Dashes
Digits in Morse code follow a beautifully simple rule: every digit is exactly five signals, and the number of dots counts up from 1 to 5, then the pattern reverses. The digit 1 is one dot followed by four dashes (.—-), 2 is two dots and three dashes (..—), and so on until 5, which is five dots (…..). After 5, the dots are replaced by dashes one at a time: 6 is one dash and four dots (-….), 7 is two dashes and three dots (–…), 8 is three dashes and two dots (—..), and 9 is four dashes and one dot (—-.).
Zero sits at the far end of that second half: all five signals are dashes. If you can count the dots in 1–5 and the dashes in 6–9, you already know zero — it is simply what happens when there are no dots left. That is why teachers often introduce zero last in the digit series: it confirms the pattern rather than adding a new rule.
Full Morse Code Digits Table (0–9)
| Digit | Morse Code | Spoken Rhythm |
|---|---|---|
| 0 | —– | dah-dah-dah-dah-dah |
| 1 | .—- | di-dah-dah-dah-dah |
| 2 | ..— | di-di-dah-dah-dah |
| 3 | …– | di-di-di-dah-dah |
| 4 | ….- | di-di-di-di-dah |
| 5 | ….. | di-di-di-di-dit |
| 6 | -…. | dah-di-di-di-dit |
| 7 | –… | dah-dah-di-di-dit |
| 8 | —.. | dah-dah-dah-di-dit |
| 9 | —-. | dah-dah-dah-dah-dit |
Notice the symmetry. The table reads like a mirror around 5: digits 1–4 add a dot each time, while digits 6–9 add a dash each time. Zero is the mirror image of 5 — five dashes where 5 has five dots. The standard digit codes are documented in the Morse code reference on Wikipedia and in the full Morse code chart, which is worth bookmarking while you practise.
How Long Is Zero? Timing Explained
Timing is what turns dots and dashes on a page into a signal a listener can copy. The standard rules are simple: a dash is three units long, the gap between signals inside one character is one unit, the gap between characters is three units, and the gap between words is seven units.
Count zero out in units. Five dashes at three units each give 15 units, plus four one-unit gaps between them, for a total of 19 units. Compare that with 5 (…..), which is only nine units, and with the letter O (—), which is 11 units including its internal gaps. Zero is genuinely long — more than twice as long as 5 — which is one reason radio operators developed a shortcut for it, covered below.
At a slow learning speed, 19 units feels very long indeed. That is normal, and it is actually helpful: the length itself becomes a recognition clue. When you hear five long, even tones with no short dots mixed in, your brain can settle on zero before the character even finishes.
How to Send 0 in Morse Code
You do not need expensive equipment to send zero. With a telegraph key or practice oscillator, press and hold for a full dash — roughly three times as long as a dot — release briefly, and repeat five times, keeping your wrist relaxed so the dashes stay even. By sound, tapping or flashlight, use the same pattern: five long sounds or flashes with short pauses between them. The method changes; the timing does not.
Step-by-step practice drill
- Say “dah-dah-dah-dah-dah” out loud five times, keeping the dahs even.
- Tap the pattern on a table, holding each tap for a slow count of three.
- Send “0” on its own, then in pairs: 0 0, 0 5, 5 0.
- Send a short number containing zero, such as 10 or 20, and listen back if you can record yourself.
- Mix zero with letters you already know — for example, send “Z0” — so you learn to hear it in context, not only in isolation.
Examples: 0 in Real Numbers
Zero rarely travels alone. It usually appears inside a larger number, and reading whole numbers is the skill that matters. Here are some everyday examples, written out so you can practise them end to end:
- 10 — .—- —– (one, then zero)
- 20 — ..— —– (two, then zero)
- 100 — .—- —– —– (one followed by two zeroes)
- 2026 — ..— —– ..— -…. (the current year, a great practice string)
- 50 — ….. —– (five, then zero)
Notice the spacing: inside a character, signals are separated by one unit, but between characters the gap is three units. That longer pause tells the listener one digit has ended and the next has begun. When you practise, exaggerate it slightly — it feels slow, but it makes your sending far clearer.
0 vs O: The Classic Beginner Mistake
The most common confusion for beginners is between the digit 0 (—–, five dashes) and the letter O (—, three dashes). They look similar on paper and sound similar at speed, but the difference is simply counting: O has three dahs, zero has five. In a message, context usually resolves any remaining doubt — a string of digits in a frequency, a year or a score is far more likely to contain zero than the letter O.
Radio operators also use a spoken convention to remove the ambiguity entirely: in voice traffic they say “zero” for the digit and “oh” for the letter. Written Morse has no such safety net, so counting carefully is the habit that protects you. If you have been working through the alphabet series, you may remember the letter Z from our earlier guide to Z in Morse Code; comparing a three-dash letter like O with the five-dash zero side by side is a useful ear-training exercise. The same counting discipline applies to every letter in the series, from Y in Morse Code to X in Morse Code.
Cut Numbers: The Shortcut Radio Operators Use
Because zero takes 19 units — the longest of any digit — experienced operators often shorten it in fast traffic. In “cut numbers,” several dashes are reduced to a single dash, so zero is sent as a single dash, which is also the code for the letter T. This is a convention, not a second official code: it only works when both sender and receiver already know that numbers, not letters, are being sent, for example in a signal report such as “599,” sent as “5NN” (N being the cut form of 9).
Beginners should learn the full five-dash zero first and treat cut numbers as advanced shorthand to recognise later, not as a replacement. If you send a lone dash where a beginner expects a letter, you will be copied as “T,” and your number will be wrong. Learn the standard, then learn the shortcut — in that order.
Where 0 Appears in Real Morse Code Use
Zero shows up wherever numbers matter, which is almost everywhere in radio life. Amateur radio operators send frequencies, signal reports, contest exchanges and grid locators full of zeroes. A frequency, a year such as 2026, a temperature or a score all depend on zero being copied correctly.
Historically, Morse code carried numbers in railway timetables, shipping messages, weather reports and military traffic long before voice radio took over. Samuel Morse and Alfred Vail designed the original American code in the 1830s and 1840s, and the International Morse Code that followed standardised digits alongside letters. The International Telecommunication Union (ITU) later formalised the code, which is why digit codes are identical across countries today.
Tips to Remember 0 in Morse Code
- Think “five for zero, five for five”: 5 is five dots, 0 is five dashes. The pair anchors both ends of the digit pattern.
- Count, do not guess: five dahs, no dots. If you count fewer than five, you have sent O or another character.
- Use the mirror trick: recite 1–9 in order, then reverse. Zero is the natural finish of the reverse run.
- Practise in real numbers: years, ages, prices and phone numbers all contain zeroes — send a few every day.
- Listen before you speed up: recognise five even dahs at slow speed first; speed without accuracy only practises mistakes.
Frequently Asked Questions
What is 0 in Morse code?
0 in Morse code is five dashes: —–, spoken as “dah-dah-dah-dah-dah.” It is the longest digit code, lasting 19 timing units.
How is 0 different from the letter O in Morse code?
The letter O is three dashes (—) while the digit 0 is five dashes (—–). Count the dahs: three means O, five means zero. Context — whether the message is a number or a word — also helps.
Why do all Morse code digits have five signals?
The five-signal design makes digits regular and easy to learn: the number of dots rises from 1 to 5, then dashes take over from 6 to 9, with zero as five dashes at the end of the pattern. Every digit takes the same number of signals, even though their durations differ.
What is the cut number for zero?
In fast amateur radio traffic, zero is sometimes shortened to a single dash (the same as T). This is an informal convention used only when both operators know numbers are being sent. Beginners should use the full five-dash code.
How can I practise 0 in Morse code?
Say “dah-dah-dah-dah-dah” aloud, tap it, send it with a practice key or flashlight, and then practise real numbers such as 10, 100 and 2026. Mixing zero with letters and other digits builds recognition faster than drilling it alone.
Conclusion
Zero in Morse code is five dashes — long, steady and unmistakable once you know the digit pattern behind it. Learn it as the mirror of 5, practise it inside real numbers, and count your dahs carefully so it never blurs into the letter O. With that one character mastered, the whole 0–9 series falls into place, and you are ready for the next digit in the series. Keep practising a little every day, and the five long tones of zero will soon feel as natural as the dots and dashes you already know.







